Body Trace BP - Welcome to GatherMed

Welcome to a better way to monitor your blood pressure
Our method seamlessly connects the data from your blood pressure device directly to your medical provider in real-time.
Familiar devices, just seamlessly connected
And if you have a smartphone, iPhone or Android, visit app.gathermed.com to connect with your doctor and track BP Trends with your doctor.
Get App
Installing the Batteries
If this is your first time using the device:
Slide open the battery door on the back of the device.
Install the batteries provided with the device. Follow the diagram inside the battery compartment for correct polarity — the springs should align with the negative sign on the batteries.
Slide the battery door closed.
Download User Manual
Securing the Cuff
1. Plug the connector on cuff tube into the device.
2. Expose your left upper arm by removing or adjusting clothing and jewelry. Make sure blood flow is not constricted by a rolled up sleeve.
3. Open the cuff and loosen fully.

Securing the Cuff (cont.)
3. Open the cuff and loosen fully.
4. Orient the cuff so that the tube exits towards
the hand.
5. Place your arm through the cuff loop, with your palm facing up.
6. Position the cuff’s edge about an inch (2-3 cm) above the elbow.
7. Align the Ф marker (located to the right of tube exit) with the center of your arm.
Taking a Measurement
8. Tighten the cuff evenly around your arm by pulling on the end — make sure the Ф marker stays aligned with the center of your arm.
9. Wrap the end of the cuff over your arm to secure it in place. Don’t make it too tight — allow a finger to fit between the cuff and your arm.
Taking a Measurement
Lay your arm on a table with your palm facing up. The cuff should be at the same height as your heart. Sit up straight and rest your feet flat on the ground. Make sure the tube is not kinked or pinched.
Press the START/STOP button on the device to turn it on.
Taking a Measurement
12. Wait for the device to power on, and perform the measurement while inflating the cuff.
13. When the measurement concludes, results are shown on the display and the cuff automatically deflates.
14. Remove the cuff after it deflates.
Transmission to your Doctor
15. The device automatically transmits measurement results. During this process an indicator is shown in the middle of the display.
16. When the measurement is successfully transmitted, the device shows the following indication before powering off
Error Codes

Er 1
Battery low
Replace batteries with four Duracell AAs.
Er 2
Movement detected
Avoid moving or talking while taking a measurement. After securing the cuff and assuming the correct posture, consider waiting for five minutes to settle down before starting a measurement.
Er 3
Measurement out of range
Confirm that the cuff is secured correctly on your exposed arm. Remove all clothing and jewelry from your arm.
If you feel unwell, contact a medical professional.
Er 4
No cellular coverage
Move to another area, closer to a window. Use the device at a location where you get a strong cellular signal with your mobile phone.
Er 5
Cellular connection error
Move to another area, closer to a window. Use the device at a location where you get a strong cellular signal with your mobile phone.
Er 6
Data Transmission Error
Move to another area, closer to a window. Use the device at a location where you get a strong cellular signal with your mobile phone.
Er 7
Internal error
Replace batteries with four Duracell AAs. If the issue persists, contact customer support.
Er 9
Provisioning error
Retake measurement. If the issue persists, contact customer support.
Er 10
Subscription suspended
Contact customer support.
Er 11
Subscription Terminated
Contact customer support.
Er 15-24
System Error
Contact customer support.
More about your Blood Pressure Device
Notes:
If you wish to abort the measurement while the cuff is inflating, press and hold the START / STOP button
for 5 seconds.
If the device detects an irregular heartbeat, the display will show this indicator along with the measurement results. While this may not be a reason for immediate concern, contact your primary care provider if you see this symbol frequently.
Precautions
Only use Duracell alkaline AA batteries with this device as these offer the longest battery life. Other brands may not be able provide sufficient power for cellular data transmission.
This device is for adults. Do not use it on children unless otherwise instructed by a medical professional.
Do not use or store the device near infants or in an area they can reach.
Do not apply the cuff on an arm that has:
• an unhealed wound,
• another medical device attached, or
• an intravenous drip or blood transfusion attached.
Do not use this device if you have an implanted cardiac device, such as a pacemaker or defibrillator.
Measurements performed by this device may not be accurate during pregnancy.
This device is intended for indoor, home use.
If in doubt, contact your medical professional before use.
Do not use the device where flammable gases are present, or in environments with high oxygen concentration.
Measurements may not be accurate if the device is used in close to proximity devices generating strong electromagnetic fields, such as microwave ovens, wireless charging stations, X-ray machines, etc.
Wireless communication devices, such as Wi-Fi access points, mobile phones, cordless phones, may cause interference that may affect the accuracy of measurements. A minimum distance of 13 feet (4 meters) should be kept from such devices during measurement.
Troubleshooting

Technical Specifications

Intended Use

This digital blood pressure monitor was designed to measure the blood pressure and heartbeat rate of adults with an arm circumference of 22 - 42 cm (9 - 17 inches). This device is intended for indoor, home use.

Compliance Statement

FCC ID: XMR201404UC15
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation.
How to use your blood pressure device at home
Please watch this video for best practices in recording your blood pressure

Call Us

Contact

Welcome to a better way to monitor your blood pressure

Our method seamlessly connects the data from your blood pressure device directly to your medical provider in real-time.

Familiar devices, just seamlessly connected

And if you have a smartphone, iPhone or Android, visit app.gathermed.com to connect with your doctor and track BP Trends with your doctor.

Installing the Batteries

Securing the Cuff

1. Plug the connector on cuff tube into the device.2. Expose your left upper arm by removing or adjusting clothing and jewelry. Make sure blood flow is not constricted by a rolled up sleeve.3. Open the cuff and loosen fully.

Securing the Cuff (cont.)

Taking a Measurement

8. Tighten the cuff evenly around your arm by pulling on the end — make sure the Ф marker stays aligned with the center of your arm.9. Wrap the end of the cuff over your arm to secure it in place. Don’t make it too tight — allow a finger to fit between the cuff and your arm.

Taking a Measurement

Lay your arm on a table with your palm facing up. The cuff should be at the same height as your heart. Sit up straight and rest your feet flat on the ground. Make sure the tube is not kinked or pinched.Press the START/STOP button on the device to turn it on.

Taking a Measurement

12. Wait for the device to power on, and perform the measurement while inflating the cuff.13. When the measurement concludes, results are shown on the display and the cuff automatically deflates.14. Remove the cuff after it deflates.

Transmission to your Doctor

15. The device automatically transmits measurement results. During this process an indicator is shown in the middle of the display.16. When the measurement is successfully transmitted, the device shows the following indication before powering off

Error Codes

Er 1

Er 2

Er 3

Er 4

Er 5

Er 6

Er 7

Er 9

Er 10

Er 11

Er 15-24

More about your Blood Pressure Device

Notes:

Precautions

How to use your blood pressure device at home

Please watch this video for best practices in recording your blood pressure

1. Plug the connector on cuff tube into the device.
2. Expose your left upper arm by removing or adjusting clothing and jewelry. Make sure blood flow is not constricted by a rolled up sleeve.
3. Open the cuff and loosen fully.

8. Tighten the cuff evenly around your arm by pulling on the end — make sure the Ф marker stays aligned with the center of your arm.
9. Wrap the end of the cuff over your arm to secure it in place. Don’t make it too tight — allow a finger to fit between the cuff and your arm.

Lay your arm on a table with your palm facing up. The cuff should be at the same height as your heart. Sit up straight and rest your feet flat on the ground. Make sure the tube is not kinked or pinched.
Press the START/STOP button on the device to turn it on.

12. Wait for the device to power on, and perform the measurement while inflating the cuff.
13. When the measurement concludes, results are shown on the display and the cuff automatically deflates.
14. Remove the cuff after it deflates.

15. The device automatically transmits measurement results. During this process an indicator is shown in the middle of the display.
16. When the measurement is successfully transmitted, the device shows the following indication before powering off